Roof Report

Installation Guideline Tips For TPO featured image

Installation Guideline Tips For TPO

Thermoplastic polyolefin (TPO) is the fastest-growing segment of the commercial roofing industry. These membranes are used for mechanically attached, adhered, and induction welded roofing systems.

Manufacturers continue to work on improving the formulations of their products for the best possible performance in our industry. Still, the essential component of TPO’s long-term performance is proper TPO installation techniques by Roofing Contractors. Hot-air welding of the seams was identified by manufacturers as the practice where most significant mistakes were being made by contractors that can lead to substantial problems as severe as roof failures years down the line.

Below are some guidelines and tips from manufacturers, contractors, and my observations over the years to assure a successful and long performing installation.

Power Needs

Using adequately sized and maintained generators with a minimum of 10k watt output is essential for the performance of your automated welder. No other equipment, such as screw guns, hand welders, etc., should use that generator for a power source. Your extension cord should be a 12-gauge minimum to meet the requirements of the welder.

Test Welds

Test welds should be done twice daily, at a minimum, at the start of the day and after the crew’s lunch break. You should also do test welds whenever the machine is restarted, or you have concerns about the integrity of the weld. You want to avoid both excessive heat and also too cold of welding temperatures. Extreme heat destroys the polymer stabilizers in the TPO and leads to premature membrane deterioration. Too cold of a welding temperature leads to false welds. This condition appears welded when probed but then alter pulls apart at the welded seam causing water infiltration into the system and building. Test welds will assure that you have proper welding temperature and speed throughout your installation. Welding temperature should be the lowest temperature possible that will still provide good seams at the machines set production speeds.

Welder Drag

Welder drag is a condition caused by improper alignment of the inside edge of the nozzle with the edge of the roller. If this is not done correctly, improper alignment of the hot-air nozzle creates gouges in the membrane outside of the seam. This condition is the second most common cause of premature membrane deterioration.

Seam Probing

The weld must be allowed to cool before being probed. Seam probing for checking seam quality is one of the misused techniques to assure maximum performance. I have seen this done incorrectly not only by installers but also by specifiers, third party quality control personnel, and yes, even manufacture inspectors. When probing, your tool should be blunt and not sharpened to a point. Blunt probes can become pointed from general use and should be checked to verify they are not too sharp before use. An overly sharp probe will unnecessarily dig into the membrane, causing damage.  It is essential when probing seams to use caution because incorrect probing can lead to problems down the line.

Hand Welding

Hand welders need to be dialed in the same as the automatic units. Keep in mind that the membrane will withstand higher temperatures, but items like prefabricated corners, boots, and T-patches will only tolerate lower temperatures. Hand welding should only be done when you can’t run an automated welder.

All hand welds should be done in two passes.

  • The first pass creates the air dam and preheats the membrane
  • On the second pass, both the welder and roller are to be perpendicular to each other on a 45-degree angle as it passes along the seam.

Membrane Age and Cleaning

Your goal is to complete all welding before the end of each workday, but most projects will require some additional welding after the initial day of install. For example, patches over punctures or additional penetrations being added. Use TPO cleaners and allow the solvent to flash off before welding.

Following these guidelines for hot air welding and referring to the membrane manufacturer’s specification manuals as well as always incorporating internal quality control measures in your installations will give you a quality and long-lasting roof every time.


John Kenney has over 45 years’ experience in the roofing industry. John started his career by working as a roofing apprentice at a family business in the Northeast to operating multiple Top 100 Roofing Contractors. As Chief Operating Officer, John is intimately familiar with all aspects of roofing production, estimating, and operations. During his tenure in the industry, John ran business units associated with delivering great workmanship and unparalleled customer service while ensuring strong net profits for his company prior to joining Cotney Consulting Group. If you would like any further information on this or another subject, you can contact John at